Soybean car

World's first plastic car
Plastic car frame patent 2,269,452 (February 13, 1942)[1]
Soybean car frame patent, Fig. 2

The soybean car, more recently referred to as the hemp body car, was a car built with agricultural plastic. Although the formula used to create the plasticized panels has been lost, it is conjectured that the first iteration of the body was made partially from soybeans and hemp.[2][upper-alpha 1][4] The body was lighter and therefore more fuel efficient than a normal metal body.[5] It was made by Ford in Dearborn, Michigan, through the work of scientist/botanist George Washington Carver and was introduced to public view on August 13, 1941.[2] It was made, in part, as a hedge against the rationing of steel during World War II.[6][7] It was designed to run on hemp fuel.[8]

History

Henry Ford first put Eugene Turenne Gregorie of his design department in charge of manufacturing. Ultimately he was not satisfied with the proposed project, and gave the project to the Soybean Laboratory in Greenfield Village. The person in charge there was Lowell Overly, who had a background in tool and die design. The finished prototype was exhibited in 1941 at the Dearborn Days festival in Dearborn, Michigan. It was also shown at the Michigan State Fair Grounds the same year.[1]

Because of World War II all US automobile production was curtailed considerably, and the plastic car experiment basically came to a halt. By the end of the war the plastic car idea went into oblivion.[2] According to Lowell Overly, the prototype car was destroyed by Bob Gregorie.[1]

Others argue that Ford invested millions of dollars into research to develop the plastic car to no avail.[9] He proclaimed he would "grow automobiles from the soil" however it never happened, even though he had over 12,000 acres of soybeans for experimentation. Some sources even say the Soybean Car wasn't made from soybeans at all but of phenolic plastic, an extract of coal tar.[10][11][12] One newspaper even reports that all of Ford's research only provided whipped cream as a final product.[10]

Reasoning for a plastic car

The Henry Ford Museum[7] gives three reasons for Ford's decision to make a plastic automobile, the plastic car made from soybeans.[13]

  1. Ford was looking to integrate industry with agriculture;
  2. Ford claimed that his plastic made these cars safer than normal metal cars;
  3. Ford wished to make his new plastic material a replacement for the metals used in normal cars. A side benefit would have been easing of the shortage of metal during World War II.[2]

Car ingredients

The frame of this automobile was made of tubular steel, to which were attached some fourteen plastic panels,[upper-alpha 2] said to be "only a quarter of an inch (6 mm) thick."[12] The windows were made of acrylic sheets. All of this led to a reduction in weight from 2500 pounds for a typical car to 1900 pounds, a reduction in weight of about 25 percent.[3][14][15]

The exact ingredients of the plastic are not known since there were no records kept of the plastic itself. Speculation is that it was a combination of soybeans, wheat, hemp, flax and ramie. Lowell Overly, the person who had the most influence in creating the car, says it was "...soybean fiber in a phenolic resin with formaldehyde used in the impregnation."[14]

Internet video

A report circulating on the Internet shows a film from 1941 about the plastic car in the opening credits as being the plastic soybean car, but at the end part it shows images of Henry Ford striking a hammer or axe onto a trunk lid.[16] It is not the Soybean Car he is hitting, but Ford's personal car with a plastic panel of the same material on the trunk,[13] and the hammer had a rubber boot placed on the sharp end of the ax.[14] When Jack Thompson, the narrator of the 1941 black and white film, stated in the introduction that this was the Soybean Car being shown he did not make it clear that the trunk Henry Ford was hitting with the tool at the end of the film was actually Ford's personal car made of the same plastic material—not the Soybean Car itself.[4] Henry Ford was doing this demonstration to show the toughness of the plastic material.[15] The demonstration was dramatic, since the tool rebounded with much force and a picture of this was shown worldwide.[17]

See also

References

Notes

  1. "The first plastic car was manufactured by the Ford Motor Company, Dearborn, Mich., USA, in August 1941. Fourteen plastic panels were mounted on a tubular welded frame."[3]
  2. "Fourteen plastic panels were mounted on a tubular welded frame."[3]

Citations

  1. 1 2 3 Ford, Henry; Gregorie, Eugene T. (January 13, 1942). "Patent 2,269,452, Automobile Chassis Construction". United States Patent Office. p. 1. Retrieved October 20, 2012.
  2. 1 2 3 4 Woodyard 2010.
  3. 1 2 3 Anzovin 2000, p. 189.
  4. 1 2 Davis 2011.
  5. Tomes 2010, p. 6.
  6. McCann-Erickson, Inc. (August 14, 1941). "Ford Completes First Plastic Body as Steel Goes on Priority List" (Press release). Penobscot Building, Detroit, Michigan.
  7. 1 2 "Soybean Car". Popular Research Topics. Dearborn, Michigan: Benson Ford Research Center The Henry Ford. Retrieved June 6, 2015.
  8. Rowan Robinson, The Great Book of Hemp: The Complete Guide to the Environmental, Commercial, and Medicinal Uses of the World's Most Extraordinary Plant, Inner Traditions, Bear & Co, 1996, p. 198.
  9. Allen & Robertson 2002, p. 121.
  10. 1 2 "Soybean Car dream goes awry: It's cream (Section A)". Deseret News and Telegram. Salt Lake City. April 8, 1954. p. 17.
  11. Bryan 1993, p. 48.
  12. 1 2 Maxwell 1994, p. 93.
  13. 1 2 Bayman 2007.
  14. 1 2 3 Benson Ford Research Center (2011). "Soybean Car". The Henry Ford. Retrieved October 20, 2012. including an extensive bibliography.
  15. 1 2 Bial 2007, p. 33.
  16. Henry Ford Plastic Car
  17. Prestige Publications 1979, p. 425.

Sources

Further reading

External links

This article is issued from Wikipedia - version of the 5/29/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.